Important Notice: The City of Marlin is transitioning to a new domain! We are moving to our new website address soon: www.marlin.texas.gov. Please update your bookmarks and email contacts. For inquiries, please contact the Office of Information Technology and Communications

2024 CCR

2

of

8

06/30/2025

TX0730002_2024_2025-06-30_14-51-49.DOC

2024 Consumer Confidence Report for Public Water System CITY OF MARLIN

This is your water quality report for January 1 to December 31, 2024

For more information regarding this report contact:

CITY OF MARLIN provides surface water from the Marlin New City Lake located in Falls County.

Name   _Richard Cohrs or water plant staff_______

Phone  ______254-338-3371__________________

Este reporte incluye información importante sobre el agua para tomar.  Para asistencia en español, favor de llamar al telefono (254) 883-1450.

Definitions and Abbreviations

Definitions and Abbreviations

The following tables contain scientific terms and measures, some of which may require explanation.

Action Level:

The concentration of a contaminant which, if exceeded, triggers treatment or other requirements which a water system must follow.

Avg:  

Regulatory compliance with some MCLs are based on running annual average of monthly samples.

Level 1 Assessment:

A Level 1 assessment is a study of the water system to identify potential problems and determine (if possible) why total coliform bacteria have been found in our water system.

Level 2 Assessment:

A Level 2 assessment is a very detailed study of the water system to identify potential problems and determine (if possible) why an E. coli MCL violation has occurred and/or why total coliform bacteria have been found in our water system on multiple occasions.

Maximum Contaminant Level or MCL:

The highest level of a contaminant that is allowed in drinking water. MCLs are set as close to the MCLGs as feasible using the best available treatment technology.

Maximum Contaminant Level Goal or MCLG:

The level of a contaminant in drinking water below which there is no known or expected risk to health. MCLGs allow for a margin of safety.

Maximum residual disinfectant level or MRDL:

The highest level of a disinfectant allowed in drinking water. There is convincing evidence that addition of a disinfectant is necessary for control of microbial contaminants.

Maximum residual disinfectant level goal or MRDLG:

The level of a drinking water disinfectant below which there is no known or expected risk to health. MRDLGs do not reflect the benefits of the use of disinfectants to control microbial contaminants.

MFL

million fibers per liter (a measure of asbestos)

mrem:

millirems per year (a measure of radiation absorbed by the body)

na:  

not applicable.

NTU

nephelometric turbidity units (a measure of turbidity)

pCi/L

picocuries per liter (a measure of radioactivity)

3

of

8

06/30/2025

TX0730002_2024_2025-06-30_14-51-49.DOC

Definitions and Abbreviations

ppb:  

micrograms per liter or parts per billion

ppm:  

milligrams per liter or parts per million

ppq

parts per quadrillion, or picograms per liter (pg/L)

ppt

parts per trillion, or nanograms per liter (ng/L)

Treatment Technique or TT:

A required process intended to reduce the level of a contaminant in drinking water.

Information about your Drinking Water

The sources of drinking water (both tap water and bottled water) include rivers, lakes, streams, ponds, reservoirs, springs, and wells.  As water travels over the surface of the land or through the ground, it dissolves naturally-occurring minerals and, in some cases, radioactive material, and can pick up substances resulting from the presence of animals or from human activity.

Drinking water, including bottled water, may reasonably be expected to contain at least small amounts of some contaminants.  The presence of contaminants does not necessarily indicate that water poses a health risk.  More information about contaminants and potential health effects can be obtained by calling the EPAs Safe Drinking Water Hotline at (800) 426-4791.

Contaminants that may be present in source water include:

–   Microbial contaminants, such as viruses and bacteria, which may come from sewage treatment plants, septic systems, agricultural livestock operations, and wildlife.

–   Inorganic contaminants, such as salts and metals, which can be naturally-occurring or result from urban storm water runoff, industrial or domestic wastewater discharges, oil and gas production, mining, or farming.

–   Pesticides and herbicides, which may come from a variety of sources such as agriculture, urban storm water runoff, and residential uses.

–   Organic chemical contaminants, including synthetic and volatile organic chemicals, which are by-products of industrial processes and petroleum production, and can also come from gas stations, urban storm water runoff, and septic systems.

–   Radioactive contaminants, which can be naturally-occurring or be the result of oil and gas production and mining activities.

In order to ensure that tap water is safe to drink, EPA prescribes regulations which limit the amount of certain contaminants in water provided by public water systems. FDA regulations establish limits for contaminants in bottled water which must provide the same protection for public health.

Contaminants may be found in drinking water that may cause taste, color, or odor problems.  These types of problems are not necessarily causes for health concerns.  For more information on taste, odor, or color of drinking water, please contact the system’s business office.

You may be more vulnerable than the general population to certain microbial contaminants, such as Cryptosporidium, in drinking water.  Infants, some elderly, or immunocompromised persons such as those undergoing chemotherapy for cancer; persons who have undergone organ transplants; those who are undergoing treatment with steroids; and people with HIV/AIDS or other immune system disorders, can be particularly at risk from infections. You should seek advice about drinking water from your physician or health care providers.  Additional guidelines on appropriate means to lessen the risk of infection by Cryptosporidium are available from the Safe Drinking Water Hotline (800-426-4791).

4

of

8

06/30/2025

TX0730002_2024_2025-06-30_14-51-49.DOC

If present, elevated levels of lead can cause serious health problems, especially for pregnant women and young children. Lead in drinking water is primarily from materials and components associated with service lines and home plumbing. We are responsible for providing high quality drinking water, but we cannot control the variety of materials used in plumbing components. When your water has been sitting for several hours, you can minimize the potential for lead exposure by flushing your tap for 30 seconds to 2 minutes before using water for drinking or cooking. If you are concerned about lead in your water, you may wish to have your water tested. Information on lead in drinking water, testing methods, and steps you can take to minimize exposure is available from the Safe Drinking Water Hotline or at http://www.epa.gov/safewater/lead.

Information about Source Water

TCEQ completed an assessment of your source water, and results indicate that some of our sources are susceptible to certain contaminants. The sampling requirements for your water system is based on this susceptibility and previous sample data. Any detections of these contaminants will be found in this Consumer Confidence Report. For more information on source water assessments and protection efforts at our system contact [insert water system contact][insert phone number]

Lead and Copper

Date Sampled

MCLG

Action Level (AL)

90th Percentile

# Sites Over AL

Units

Violation

Likely Source of Contamination

Copper

2024

1.3

1.3                                    

0.3414

1

ppm      

N

Erosion of natural deposits; Leaching from wood preservatives; Corrosion of household plumbing systems.

Lead

2024

0

15                                      

0

1

ppb      

N

Corrosion of household plumbing systems; Erosion of natural deposits.

2024 Water Quality Test Results

2024

Disinfection By-Products

Collection Date

Highest Level Detected

Range of Individual Samples

MCLG

MCL

Units

Violation

Likely Source of Contamination

Haloacetic Acids (HAA5)

2024

92

13.3 – 143

No goal for the total

60                                      

ppb      

Y

By-product of drinking water disinfection.

*The value in the Highest Level or Average Detected column is the highest average of all HAA5 sample results collected at a location over a year

5

of

8

06/30/2025

TX0730002_2024_2025-06-30_14-51-49.DOC

Total Trihalomethanes (TTHM)

2024

84

50.3 – 97.7

No goal for the total

80                                      

ppb      

Y

By-product of drinking water disinfection.

*The value in the Highest Level or Average Detected column is the highest average of all TTHM sample results collected at a location over a year

2024

Inorganic Contaminants

Collection Date

Highest Level Detected

Range of Individual Samples

MCLG

MCL

Units

Violation

Likely Source of Contamination

Barium

2024

0.069

0.069 – 0.069

2

2                                      

ppm      

N

Discharge of drilling wastes; Discharge from metal refineries; Erosion of natural deposits.

Chromium

2024

22

22 – 22

100

100                                    

ppb      

N

Discharge from steel and pulp mills; Erosion of natural deposits.

Fluoride

2024

0.1

0.0888 – 0.0888

4

4.0                                    

ppm      

N

Erosion of natural deposits; Water additive which promotes strong teeth; Discharge from fertilizer and aluminum factories.

Nitrate [measured as Nitrogen]

2024

0.063

0.063 – 0.063

10

10                                      

ppm      

N

Runoff from fertilizer use; Leaching from septic tanks, sewage; Erosion of natural deposits.

2024

Radioactive Contaminants

Collection Date

Highest Level Detected

Range of Individual Samples

MCLG

MCL

Units

Violation

Likely Source of Contamination

Beta/photon emitters

03/17/2022

5.5

5.5 – 5.5

0

50                                      

pCi/L*  

N

Decay of natural and man-made deposits.

*EPA considers 50 pCi/L to be the level of concern for beta particles.

Combined Radium 226/228

03/17/2022

1.5

1.5 – 1.5

0

5                                      

pCi/L    

N

Erosion of natural deposits.

2024

Synthetic organic contaminants including pesticides and herbicides

Collection Date

Highest Level Detected

Range of Individual Samples

MCLG

MCL

Units

Violation

Likely Source of Contamination

Di (2-ethylhexyl) phthalate

2024

2

1.9 – 1.9

0

6                                      

ppb      

N

Discharge from rubber and chemical factories.

Disinfectant Residual

A blank disinfectant residual table has been added to the CCR template, you will need to add data to the fields. Your data can be taken off the Disinfectant Level Quarterly Operating Reports (DLQOR).

6

of

8

06/30/2025

TX0730002_2024_2025-06-30_14-51-49.DOC

Disinfectant Residual

A blank disinfectant residual table has been added to the CCR template, you will need to add data to the fields. Your data can be taken off the Disinfectant Level Quarterly Operating Reports (DLQOR).

Disinfectant Residual

Year

Average Level

Range of Levels Detected

MRDL

MRDLG

Unit of Measure

Violation (Y/N)

Source in Drinking Water

Chloramine & Free CL2

2024

3.10 mg/L

1.67 4.5 mg/L

4

4

mg/L

ppm      

Water additive used to control microbes.

Turbidity

Level Detected

Limit (Treatment Technique)

Violation

Likely Source of Contamination

Highest single measurement

0.69 NTU          

1 NTU      

N

Soil runoff.

Lowest monthly % meeting limit

98%              

0.3 NTU    

N

Soil runoff.

Information Statement:  Turbidity is a measurement of the cloudiness of the water caused by suspended particles.  We monitor it because it is a good indicator of water quality and the effectiveness of our filtration system and disinfectants.

Total Organic Carbon

The percentage of Total Organic Carbon (TOC) removal was measured each month and the system met all TOC removal requirements set, unless a TOC violation is noted in the violations section.

Violations

Haloacetic Acids (HAA5)

Some people who drink water containing haloacetic acids in excess of the MCL over many years may have an increased risk of getting cancer.

Violation Type

Violation Begin

Violation End

Violation Explanation

FAILURE SUBMIT OEL REPORT FOR HAA5

06/03/2024

09/05/2024

We failed to submit our operational evaluation level (OEL) report to our regulator. The  report is needed to determine best treatment practices necessary to minimize possible future exceedences of HAA5.

MCL, LRAA

01/01/2024

03/31/2024

Water samples showed that the amount of this contaminant in our drinking water was above its standard (called a maximum contaminant level and abbreviated MCL) for the period indicated.

MCL, LRAA

04/01/2024

06/30/2024

Water samples showed that the amount of this contaminant in our drinking water was above its standard (called a maximum contaminant level and abbreviated MCL) for the period indicated.

MCL, LRAA

07/01/2024

09/30/2024

Water samples showed that the amount of this contaminant in our drinking water was above its standard (called a maximum contaminant level and abbreviated MCL) for the period indicated.

7

of

8

06/30/2025

TX0730002_2024_2025-06-30_14-51-49.DOC

Violations

Public Notification Rule

The Public Notification Rule helps to ensure that consumers will always know if there is a problem with their drinking water. These notices immediately alert consumers if there is a serious problem with their drinking water (e.g., a boil water emergency).

Violation Type

Violation Begin

Violation End

Violation Explanation

PUBLIC NOTICE RULE LINKED TO VIOLATION

04/14/2024

2024

We failed to adequately notify you, our drinking water consumers, about a violation of the drinking water regulations.

PUBLIC NOTICE RULE LINKED TO VIOLATION

08/24/2024

09/24/2024

We failed to adequately notify you, our drinking water consumers, about a violation of the drinking water regulations.

Total Trihalomethanes (TTHM)

Some people who drink water containing trihalomethanes in excess of the MCL over many years may experience problems with their liver, kidneys, or central nervous systems, and may have an increased risk of getting cancer.

Violation Type

Violation Begin

Violation End

Violation Explanation

MCL, LRAA

04/01/2024

06/30/2024

Water samples showed that the amount of this contaminant in our drinking water was above its standard (called a maximum contaminant level and abbreviated MCL) for the period indicated.

8

of

8

06/30/2025

TX0730002_2024_2025-06-30_14-51-49.DOC

8

of

8

06/30/2025

TX0730002_2024_2025-06-30_14-51-49.DOC

Mandatory Language for a Maximum Contaminant Level Violation

MCL, LRAA/ TOTAL HALOACETIC ACIDS (HAA5)

The Texas Commission on Environmental Quality (TCEQ) has notified the City of Marlin public water system that the drinking water being supplied to customers had exceeded the Maximum Contaminant Level (MCL) for total haloacetic acids. The U.S. Environmental Protection Agency (U.S. EPA) has established the MCL for total haloacetic acids to be 0.060 milligrams per liter (mg/L) based on a locational running annual average (LRAA), and has determined that it is a health concern at levels above the MCL. Analysis of drinking water in your community for total haloacetic acids indicates a compliance value for01/01/2024 – 3/3/2024 of .065 mg/L at sample point DS01/DBP2-02.

Haloacetic acids are a group of volatile organic compounds that are formed when chlorine, added to the water during the treatment process for disinfection, reacts with naturallyoccurring organic matter in the water.

Some people who drink water containing haloacetic acids in excess of the MCL over many years may have an increased risk of getting cancer.

You do not need to use an alternative water supply. However, if you have health concerns, you may want to talk to your doctor to get more information about how this may affect you.

We are taking the following actions to address this issue:

The City of Marlin has received approval from TCEQ to inject sodium permanganate. This will oxidize iron and manganese as pretreatment to our Membrane filters. Currently we are using free chlorine which is another oxidant. Unfortunately, Free chlorine creates biproducts such as Haloacetic acids. Our hope is that we will be using sodium permanganate before the end of the summer 2015.

Please share this information with all people who drink this water, especially those who may not have received this notice directly (i.e., people in apartments, nursing homes, schools, and businesses). You can do this by posting this notice in a public place or distributing copies by hand or mail.

If you have questions regarding this matter, you may contact _Richard Cohrs______ at

__254-883-3371___.  

Posted /Delivered on: _6/27/2025_

Mandatory Language for a Maximum Contaminant Level Violation

MCL, LRAA/ TOTAL HALOACETIC ACIDS (HAA5)

The Texas Commission on Environmental Quality (TCEQ) has notified the City of Marlin public water system that the drinking water being supplied to customers had exceeded the Maximum Contaminant Level (MCL) for total haloacetic acids. The U.S. Environmental Protection Agency (U.S. EPA) has established the MCL for total haloacetic acids to be 0.060 milligrams per liter (mg/L) based on a locational running annual average (LRAA), and has determined that it is a health concern at levels above the MCL. Analysis of drinking water in your community for total haloacetic acids indicates a compliance value for04/01/20246/30/2024 of .087 mg/L at sample point DS01/DBP2-02.

Haloacetic acids are a group of volatile organic compounds that are formed when chlorine, added to the water during the treatment process for disinfection, reacts with naturallyoccurring organic matter in the water.

Some people who drink water containing haloacetic acids in excess of the MCL over many years may have an increased risk of getting cancer.

You do not need to use an alternative water supply. However, if you have health concerns, you may want to talk to your doctor to get more information about how this may affect you.

We are taking the following actions to address this issue:

The City of Marlin has received approval from TCEQ to inject sodium permanganate. This will oxidize iron and manganese as pretreatment to our Membrane filters. Currently we are using free chlorine which is another oxidant. Unfortunately, Free chlorine creates biproducts such as Haloacetic acids. Our hope is that we will be using sodium permanganate before the end of the summer 2015.

Please share this information with all people who drink this water, especially those who may not havereceived this notice directly (i.e., people in apartments, nursing homes, schools, and businesses). You can do this by posting this notice in a public place or distributing copies by hand or mail.

If you have questions regarding this matter, you may contact _Richard Cohrs______ at

__254-883-3371___.  

Posted /Delivered on: _6/27/2025_

Mandatory Language for a Maximum Contaminant Level Violation

MCL, LRAA/ TOTAL HALOACETIC ACIDS (HAA5)

The Texas Commission on Environmental Quality (TCEQ) has notified the City of Marlin public water system that the drinking water being supplied to customers had exceeded the Maximum Contaminant Level (MCL) for total haloacetic acids. The U.S. Environmental Protection Agency (U.S. EPA) has established the MCL for total haloacetic acids to be 0.060 milligrams per liter (mg/L) based on a locational running annual average (LRAA), and has determined that it is a health concern at levels above the MCL. Analysis of drinking water in your community for total haloacetic acids indicates a compliance value for07/01/2024 – 9/30/2024 of .082 mg/L at sample point DS01/DBP2-02.

Haloacetic acids are a group of volatile organic compounds that are formed when chlorine, added to the water during the treatment process for disinfection, reacts with naturallyoccurring organic matter in the water.

Some people who drink water containing haloacetic acids in excess of the MCL over many years may have an increased risk of getting cancer.

You do not need to use an alternative water supply. However, if you have health concerns, you may want to talk to your doctor to get more information about how this may affect you.

We are taking the following actions to address this issue:

The City of Marlin has received approval from TCEQ to inject sodium permanganate. This will oxidize iron and manganese as pretreatment to our Membrane filters. Currently we are using free chlorine which is another oxidant. Unfortunately, Free chlorine creates biproducts such as Haloacetic acids. Our hope is that we will be using sodium permanganate before the end of the summer 2015.

Please share this information with all people who drink this water, especially those who may not havereceived this notice directly (i.e., people in apartments, nursing homes, schools, and businesses). You can do this by posting this notice in a public place or distributing copies by hand or mail.

If you have questions regarding this matter, you may contact _Richard Cohrs______ at

__254-883-3371___.  

Posted /Delivered on: _6/27/2025_

8

of

8

06/30/2025

TX0730002_2024_2025-06-30_14-51-49.DOC

 

Close window